| Introduction |
 | Contents |
| s300 |
| Differences between the s100, s200 and s300 |
| Differences between the S300 and S300J |
| What's new in this version |
| Copyright |
| Software License Agreement |
| s300 Installation |
| Installation Overview |
| Installing SManager software |
| Installing the ECU in the Vehicle |
| Installing USB drivers (XP) |
| Installing USB Drivers (Vista) |
| s300 ECU Socketing |
| Calibrations |
| Introduction to Calibrations |
| Uploading Calibrations to the ECU |
| Upgrading Calibration Files |
| Upgrading V3 Files |
| Datalogging |
| Introduction to datalogging |
| On Board Datalogging |
| Sensor Setup |
| Export Datalog |
| Export Movie |
| Tuning your vehicle |
| Tuning fuel tables |
| Tuning ignition tables |
| Tuning the VTEC point |
| Tuning ITBs |
| Setting the Idle Speed |
| Windows |
| Settings |
| General Settings |
| Units Settings |
| Sensor Overlay Settings |
| Target Lambda Settings |
| Analog Input Settings |
| Autotune Settings |
| Main Window |
| Undo History |
| New Calibration |
| Create Forced Induction Tables |
| Adjust Selected Values |
| Table Window |
| Lambda Overlay |
| Changing Table Index Values |
| Graph Window |
| Datalog Comments |
| Graph Templates |
| Parameters Window |
| Boost Control |
| Boost Control ECU Preparation |
| Boost Control Solenoid Installation |
| Boost Control Parameters |
| Boost Control Example Graphs |
| Boost Parameters |
| Closed Loop Parameters |
| Wideband Lambda Parameters |
| Datalogging Parameters |
| Fuel Compensation Parameters |
| Fuel Trim Parameters |
| Full Throttle Shift Parameters |
| Gear Compensation Parameters |
| Idle Parameters |
| Ignition Compensation Parameters |
| Launch Control Parameters |
| MAP Parameters |
| MAP Scalar and Offset |
| Adding a MAP Sensor |
| Misc Parameters |
| Nitrous Parameters |
| Protection Parameters |
| Rev Limit Parameters |
| Secondary Tables |
| Shift Light Parameters |
| TPS Parameters |
| VTEC Parameters |
| Notes Parameters |
| Sensor Window |
| Display Window |
| Error Codes Window |
| ECU Information Window |
| Commands |
| Email Files |
| Compare Calibrations |
| Upload |
| Download |
| Set Ignition Timing |
| Information |
| Clear DTCs |
| Check for Updates |
| Reference |
| Sensors |
| RPM |
| VSS |
| Gear |
| MAP |
| TPS |
| INJ |
| DUTY |
| IGN |
| IAT |
| ECT |
| O2 |
| S TRIM |
| L TRIM |
| K Retard |
| K Level |
| PA |
| BAT |
| ELD |
| REVL |
| IGNC |
| BstC |
| Lnch.R |
| Lnch.C |
| Shft.C |
| BKSW |
| ACSW |
| PSP |
| VTP |
| SCS |
| MIL |
| ACCL |
| VTS |
| Fuel |
| PCS |
| IAB |
| FANC |
| ALTC |
| N1Arm |
| N1On |
| N2Arm |
| N2On |
| Data |
| Frame |
| IAT.c |
| ECT.c |
| PWM |
| Analog Input 1 |
| Analog Input 2 |
| A10 |
| Sec Table |
| ECU Connectors |
| Error Codes |
| Switch Inputs |
| Vista Virtualization |
| Troubleshooting |
| USB troubleshooting |
| ECU troubleshooting |
© 2010 Hondata, Inc.